{"product_id":"heat-shrink-ring-terminal-8-awg-1-4-stud-25-pack-1385313","title":"Heat Shrink Ring Terminal 8 AWG 1\/4\" Stud 25-Pack (1385313)","description":"\u003ch2\u003eHeat Shrink Ring Terminal — 8 AWG, 1\/4\" Stud, 25-Pack\u003c\/h2\u003e\u003cp\u003eTerminate heavy-gauge wiring at panel-size studs with a fully sealed, corrosion-proof connection. These adhesive-lined heat shrink ring terminals combine an 8 AWG tinned copper crimp barrel with a dual-wall heat shrink sleeve — delivering a watertight termination at 1\/4\" studs for high-current circuits including bilge pumps, windlasses, solenoids, and heavy accessory feeds routed to distribution panels.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual-Wall Adhesive-Lined Heat Shrink\u003c\/strong\u003e — Inner adhesive melts and seals the crimp zone during heating, locking out moisture and preventing galvanic corrosion at the wire-to-terminal interface\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e8 AWG Heavy-Gauge Rating\u003c\/strong\u003e — Handles the current demands of windlasses, thrusters, bilge pumps, inverters, and other high-draw accessories\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1\/4\" Stud Size\u003c\/strong\u003e — Fits the 1\/4\" (#10) studs on fuse blocks, distribution panels, solenoid terminals, and circuit breakers where heavy-gauge feeds terminate at panel-size hardware\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTinned Copper Barrel\u003c\/strong\u003e — Corrosion-resistant construction maintains low contact resistance and long-term conductivity in salt and humid marine environments\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClosed-Ring Design\u003c\/strong\u003e — Ring cannot back off the stud under vibration, ensuring a permanent, secure connection at critical high-current points\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e25-Pack Quantity\u003c\/strong\u003e — Covers a full wiring project or keeps your onboard spares kit well stocked\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Heat shrink ring terminal (adhesive-lined, dual-wall)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWire Gauge:\u003c\/strong\u003e 8 AWG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStud Size:\u003c\/strong\u003e 1\/4\"\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBarrel:\u003c\/strong\u003e Tinned copper\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSleeve:\u003c\/strong\u003e Dual-wall adhesive-lined heat shrink\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 25 per pack\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e High-current accessory feeds, solenoids, fuse blocks, distribution panels, bilge pumps, windlasses\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU:\u003c\/strong\u003e 1385313\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003e8 AWG Heat Shrink Ring Terminal — Stud Size Comparison\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e8 AWG, 1\/4\" stud\u003c\/strong\u003e — Heavy-gauge wire to panel-size fuse blocks, solenoids, circuit breakers (this SKU — 1385313)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e8 AWG, 5\/16\" stud\u003c\/strong\u003e — Heavy-gauge wire to battery posts, main bus bars, large solenoids (SKU 1385348)\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eBoth use the same 8 AWG wire gauge — choose based on the stud size at your termination point. Measure the stud diameter or check the terminal block spec before ordering.\u003c\/p\u003e\u003ch3\u003eInstallation Notes\u003c\/h3\u003e\u003cp\u003eStrip 8 AWG wire to the correct length so the conductor fills the barrel without protruding. Use a heavy-duty ratcheting crimper rated for 8 AWG — light-duty crimpers will not produce a reliable gas-tight crimp at this gauge. Apply heat evenly with a heat gun until the sleeve shrinks uniformly and adhesive flows from both ends. Allow to cool fully before torquing the stud nut to the terminal block manufacturer's specification. Do not use an open flame — it damages the sleeve and conductor insulation.\u003c\/p\u003e\u003cp\u003eThe 1385313 bridges the gap between heavy-gauge wiring and panel-size hardware — the right terminal when your 8 AWG run needs to land on a 1\/4\" stud with a fully sealed, vibration-proof connection.\u003c\/p\u003e","brand":"WEST","offers":[{"title":"Default Title","offer_id":43866742784036,"sku":"1385313","price":59.25,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0743\/5799\/7604\/files\/heat-shrink-ring-terminals-8-awg-321325.jpg?v=1776291716","url":"https:\/\/marisolmarine.com\/products\/heat-shrink-ring-terminal-8-awg-1-4-stud-25-pack-1385313","provider":"Marisol Marine Company","version":"1.0","type":"link"}