{"product_id":"t-h-marine-bsr1kdp-bulkhead-strain-relief-hose-kit-232-bsr1kdp","title":"T-H Marine BSR1KDP Bulkhead Strain Relief Hose Kit – .250–.485 OD, 1-1\/4\" Hole, Watertight","description":"\u003ch2\u003eT-H Marine BSR1KDP Bulkhead Strain Relief Hose Kit – .250–.485 OD, 1-1\/4\" Hole, Watertight\u003c\/h2\u003e\u003cp\u003eThe T-H Marine BSR1KDP is a bulkhead strain relief fitting kit for routing hose through a bulkhead or panel on a boat. The strain relief distributes the stress from hose bends at the bulkhead penetration point, preventing the hose from kinking, cracking, or pulling loose at the entry point over time. The watertight gripper fitting seals around the hose to prevent water intrusion through the bulkhead opening.\u003c\/p\u003e\u003cp\u003eFits hose with an outside diameter of .250\" to .485\" and requires a 1-1\/4\" installation hole in the bulkhead or panel. \u003cstrong\u003eFor bulk hose only\u003c\/strong\u003e — pre-made hoses with end fittings already installed cannot pass through the fitting.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHose OD Range:\u003c\/strong\u003e .250\" to .485\" outside diameter\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation Hole Required:\u003c\/strong\u003e 1-1\/4\"\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting Type:\u003c\/strong\u003e Watertight gripper — seals around hose to prevent water intrusion\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHose Type:\u003c\/strong\u003e Bulk hose only — pre-made hoses with end fittings cannot pass through\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart Number:\u003c\/strong\u003e BSR1KDP | SKU: 232-BSR1KDP\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCompatible Applications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRouting bulk hose through bulkheads, panels, or transom walls on boats\u003c\/li\u003e\n\u003cli\u003eAny hose with an outside diameter between .250\" and .485\"\u003c\/li\u003e\n\u003cli\u003eApplications requiring a watertight seal at the bulkhead penetration point\u003c\/li\u003e\n\u003cli\u003eSuitable for hydraulic hose, fuel line, wiring loom, and other flexible hose or tubing within the OD range\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot suitable\u003c\/strong\u003e for pre-made hoses with end fittings already installed — the fitting cannot accommodate the end fitting diameter\u003c\/li\u003e\n\u003cli\u003eVerify your hose OD is within the .250–.485\" range and that a 1-1\/4\" hole can be drilled in your bulkhead before ordering\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eParts Desk Insights\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eBest Use Case:\u003c\/strong\u003e The BSR1KDP is the right fitting when you’re routing bulk hose through a bulkhead or panel and need both a watertight seal and strain relief at the penetration point. Without a strain relief, hose that passes through a bulkhead is subject to chafing against the hole edge and stress from bends immediately after the penetration — both of which can cause premature hose failure. The watertight gripper design seals around the hose to prevent water from passing through the bulkhead opening, which is important for any penetration below or near the waterline or in areas exposed to spray. The 1-1\/4\" hole requirement is the key installation constraint — confirm you can drill or that a 1-1\/4\" hole already exists in your bulkhead before ordering. Remember this fitting is for bulk hose only: if your hose already has end fittings installed, the fitting cannot be threaded onto the hose.\u003c\/p\u003e","brand":"LNS","offers":[{"title":"Default Title","offer_id":51250854887460,"sku":"232-BSR1KDP","price":47.59,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0743\/5799\/7604\/files\/232-BSR1K.jpg?v=1786511136","url":"https:\/\/marisolmarine.com\/products\/t-h-marine-bsr1kdp-bulkhead-strain-relief-hose-kit-232-bsr1kdp","provider":"Marisol Marine Company","version":"1.0","type":"link"}