{"product_id":"turning-point-hustler-propeller-9x10-3-blade-aluminum-rh","title":"Turning Point Hustler Propeller 9x10 – 3-Blade Aluminum, RH Rotation","description":"\u003ch2\u003eHigh-Value Aluminum Propeller for Small Outboards – 6 to 20 hp\u003c\/h2\u003e\n\u003cp\u003eThe Hustler 9x10 is a 3-blade aluminum propeller engineered for small outboard engines in the 6–20 hp range with 2.5\" gearcases. One pitch step above the \u003ca href=\"\/products\/turning-point-hustler-propeller-9x9-3-blade-aluminum-rh\"\u003eHustler 9x9\u003c\/a\u003e, the 10\" pitch is suited to boats that can carry a bit more load and still reach the upper end of the engine's WOT RPM range — delivering slightly more top-end speed where conditions allow.\u003c\/p\u003e\n\n\u003cp\u003eLike all Hustler props, it brings stainless steel blade geometry and squeeze-cast construction to an aluminum price point. The exclusive squeeze-casting process produces a denser, stiffer blade with less flex under load than traditional die-cast aluminum props — resulting in better efficiency, more consistent performance, and improved durability. A five-step Ultracoat™ powder-coated finish provides long-lasting corrosion resistance and a high-gloss appearance.\u003c\/p\u003e\n\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eBlade geometry derived from stainless steel designs — not a typical die-cast aluminum prop\u003c\/li\u003e\n\u003cli\u003eSqueeze-cast construction for a denser, stiffer blade with less flex under load\u003c\/li\u003e\n\u003cli\u003eIncreased blade surface area and cupping for improved acceleration and bow lift\u003c\/li\u003e\n\u003cli\u003eLarge free-flowing exhaust ports — 40% more exhaust area for reduced backpressure\u003c\/li\u003e\n\u003cli\u003eFive-step Ultracoat™ powder-coated finish for long-lasting corrosion resistance\u003c\/li\u003e\n\u003cli\u003eRight-hand (standard) rotation\u003c\/li\u003e\n\u003cli\u003e9\" diameter × 10\" pitch, 3-blade configuration\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eEngine Compatibility\u003c\/h3\u003e\n\u003cp\u003eDesigned for 6–20 hp outboard engines with 2.5\" gearcases. Always verify fitment using the manufacturer's application chart before ordering.\u003c\/p\u003e\n\n\u003ch3\u003eRequired Hub Kit\u003c\/h3\u003e\n\u003cp\u003eA hub\/installation kit is required and sold separately. This propeller uses 200 Series hub kits only. See the \u003ca href=\"\/products\/masterguard-hub-kit-208-200-series-6-20hp-outboards-2-5-gearcase\"\u003eMasterGuard Hub Kit 208 – 200 Series\u003c\/a\u003e for a common fit, and refer to the application chart for the correct part number for your specific engine.\u003c\/p\u003e\n\n\u003chr\u003e\n\u003ch3\u003eParts Desk Insights\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eBest Use Case:\u003c\/strong\u003e Best suited to lighter aluminum fishing boats, inflatables, and small tiller-steer outboards where the engine consistently reaches the top of its WOT RPM range on the \u003ca href=\"\/products\/turning-point-hustler-propeller-9x9-3-blade-aluminum-rh\"\u003e9x9\u003c\/a\u003e. The extra inch of pitch will pull the RPM down slightly and add a small amount of top-end speed on boats that can handle it. If the engine struggles to reach WOT RPM with the 10\" pitch, step back down to the \u003ca href=\"\/products\/turning-point-hustler-propeller-9x9-3-blade-aluminum-rh\"\u003eHustler 9x9\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePitch Selection Tip:\u003c\/strong\u003e As a general rule, each inch of pitch change moves WOT RPM by approximately 150–200 RPM. Always confirm the engine's recommended WOT RPM range and test accordingly. Over-propping a small outboard can cause premature wear and reduced performance.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eAluminum vs. Stainless:\u003c\/strong\u003e At 6–20 hp, the performance gap between aluminum and stainless is minimal (typically 0.5–1 mph). The Hustler aluminum is an excellent value at this power range — stainless is harder to justify unless the customer frequently strikes debris.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eHub Kit Note:\u003c\/strong\u003e This prop uses 200 Series hub kits only — not compatible with 500 or 700 Series kits. Confirm the correct kit number from the application chart. The \u003ca href=\"\/products\/masterguard-hub-kit-208-200-series-6-20hp-outboards-2-5-gearcase\"\u003eHub Kit 208\u003c\/a\u003e covers many common 2.5\" gearcase applications.\u003c\/p\u003e","brand":"LNS","offers":[{"title":"Default Title","offer_id":51215130460196,"sku":"708-21101010","price":127.15,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0743\/5799\/7604\/files\/708-21101010.jpg?v=1786150386","url":"https:\/\/marisolmarine.com\/products\/turning-point-hustler-propeller-9x10-3-blade-aluminum-rh","provider":"Marisol Marine Company","version":"1.0","type":"link"}