{"product_id":"volvo-1234","title":"Volvo Penta — O-Ring — 925096","description":"\u003ch2\u003eVolvo Penta O-Ring 925096\u003c\/h2\u003e\u003cp\u003eGenuine Volvo Penta sealing O-ring for selected marine drive, transmission, engine, and cooling-system assemblies. Part \u003cstrong\u003e925096\u003c\/strong\u003e is commonly used at the lower bearing carrier on Volvo Penta IPS drives and in the DPH-E gear housing.\u003c\/p\u003e\u003ch3\u003eCompatible Applications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eIPS-A\u003c\/li\u003e\n\u003cli\u003eIPS-B\u003c\/li\u003e\n\u003cli\u003eIPS-C\u003c\/li\u003e\n\u003cli\u003eIPS-D\u003c\/li\u003e\n\u003cli\u003eIPS-E\u003c\/li\u003e\n\u003cli\u003eIPS-F\u003c\/li\u003e\n\u003cli\u003eDPH-E gear housing, diagram item 2\u003c\/li\u003e\n\u003cli\u003eSelected DPR-D and later IPS configurations where the parts diagram specifies 925096\u003c\/li\u003e\n\u003cli\u003eSelected coolant-pump and thermostat assemblies, including TAD1630-series applications where specified\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eBecause this O-ring appears in several unrelated assemblies, confirm compatibility using the exact Volvo Penta parts diagram rather than the engine family alone.\u003c\/p\u003e\u003ch3\u003ePart Details\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 925096\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Volvo Penta\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct type:\u003c\/strong\u003e Sealing O-ring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApproximate size:\u003c\/strong\u003e 124.5 mm inside diameter × 3.0 mm cross-section (4.90 × 0.118 in)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIPS quantity:\u003c\/strong\u003e Two used in applicable lower bearing-carrier assemblies\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlternate reference:\u003c\/strong\u003e 12330\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eReplacement Guidance\u003c\/h3\u003e\u003cp\u003eReplace the O-ring whenever the sealed component is disassembled or if inspection shows flattening, cuts, hardening, cracking, swelling, deformation, or leakage. During IPS bearing-carrier service, replacing both specified O-rings helps prevent reopening the drive for a seal leak.\u003c\/p\u003e\u003ch3\u003eInstallation Notes\u003c\/h3\u003e\u003cp\u003eClean the groove and mating surfaces before installation. Remove corrosion and debris that could pinch the new seal, and avoid twisting it during assembly. Use the lubricant and procedure specified in the applicable Volvo Penta workshop manual. For IPS service, inspect the surrounding sealing surfaces and propeller-shaft seals at the same time.\u003c\/p\u003e\u003ch3\u003eTechnical FAQ\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eDoes 925096 fit every Volvo Penta engine or drive?\u003c\/strong\u003e\u003cbr\u003eNo. It is used in several different assemblies, so the exact parts diagram must specify 925096.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many are used on an IPS lower bearing carrier?\u003c\/strong\u003e\u003cbr\u003eApplicable Volvo Penta IPS parts references specify two.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich related IPS sealing-ring numbers may appear in the same service area?\u003c\/strong\u003e\u003cbr\u003eDepending on the drive configuration, the diagram may also reference 3842286, 3842288, and 3842290.\u003c\/p\u003e\u003chr\u003e\u003ch3\u003eParts Desk Insights\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eBest use case:\u003c\/strong\u003e Replacing the specified large lower bearing-carrier seal during applicable IPS drive service, or servicing another assembly whose diagram calls for 925096.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMost common mistake:\u003c\/strong\u003e Ordering by engine family alone. This part appears in unrelated drive and cooling-system assemblies, so match the full part number and diagram position.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSizing and fitment:\u003c\/strong\u003e The published reference size is approximately 124.5 mm ID × 3.0 mm cross-section. Confirm the groove, diagram, and required quantity before installation.\u003c\/p\u003e","brand":"VOL","offers":[{"title":"Default Title","offer_id":43564058902564,"sku":"925096","price":4.9,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0743\/5799\/7604\/files\/484874ff-4985-4b2c-9e62-a6caddbfa364.png?v=1789841905","url":"https:\/\/marisolmarine.com\/products\/volvo-1234","provider":"Marisol Marine Company","version":"1.0","type":"link"}