Lowrance 000-0120-37 Yamaha Engine Interface Cable for NMEA 2000

Lowrance 000-0120-37 — Yamaha Engine Interface Cable for NMEA 2000 | 15 ft / 4.5 m

The Lowrance 000-0120-37 is a 15 ft (4.5 m) engine interface cable that connects compatible Yamaha outboards directly to an NMEA 2000 network, allowing engine data to be displayed on any NMEA 2000 compatible chartplotter or multi-function display. No Yamaha CommandLink Plus system is required. An NMEA 2000 T-connector is included.

Part Details

• Part Number: 000-0120-37
• Brand: Lowrance
• Official Product Type: Yamaha Engine Interface Cable for NMEA 2000
• Cable Length: 15 ft / 4.5 m
• Kit Contents: Engine interface cable (15 ft) + NMEA 2000 T-connector
• System: NMEA 2000 engine data integration
• UPC: 042194529820

Compatible Applications

• 2006 and newer Yamaha FourStroke outboards: F50, T50, F60, T60, F75, F90, F115, LF115, F150, LF150, F200, LF200, F225, F250, LF250
• Yamaha HPDI / 2-stroke outboards: Z150, LZ150, VZ150, Z175, Z200, LZ200, VZ225, Z250, LZ250, VZ250, Z300, LZ300, VZ300
• Any NMEA 2000 compatible display: Lowrance, Simrad, B&G, Garmin, and others
• Existing powered NMEA 2000 backbone installations

Engine Data Supported

Depending on engine model, this cable can transmit the following data to your NMEA 2000 display:

• Engine RPM
• Alternator voltage
• Engine hours
• Engine temperature
• Fuel pressure
• Fuel flow rate
• Oil pressure
• Engine trim
• Water pressure

Note: Digital trim display requires the appropriate Yamaha connection and dealer configuration on some models.

Installation Notes

• Connect the Yamaha engine end to the factory interface connector under the engine cowling — typically a white 4-pin connector on the starboard side with two wires (blue and white) already connected
• If a factory waterproof plug is installed on the connector, remove it before connecting the cable
• Connect the NMEA 2000 end to the backbone using the included T-connector
• The NMEA 2000 network must be powered and correctly terminated at both ends before commissioning the engine data connection
• If your boat does not yet have an NMEA 2000 network, a backbone starter kit is required before using this cable — see related products below

Parts Desk Insights

Best Use Case: This cable is the cleanest solution for getting Yamaha engine data onto an NMEA 2000 network when you don't want to invest in a full Yamaha CommandLink Plus setup. It's especially well-suited for boats that already have a working NMEA 2000 backbone and just need to bring the engine into the network. One cable, one T-connector, and you're done.

Common Issues: The most common installation challenge is locating and accessing the Yamaha factory 4-pin connector under the cowling — it can be tucked away and may have a factory plug installed that needs to be removed first. Also confirm your NMEA 2000 backbone has adequate capacity and a free T-connector slot before ordering. If your boat doesn't have an existing NMEA 2000 network, you'll need a starter kit (backbone cable, terminators, T-connectors, and power cable) before this interface cable will function — see the X2K-Exp-Red-2 NMEA Starter Kit below.

Technical Notes

• A powered and correctly terminated NMEA 2000 backbone is required — this cable does not include backbone cable, terminators, or a power cable
• Confirm your specific Yamaha engine model and production year against the compatibility list before installation
• For twin-engine installations, one interface cable is required per engine

Related Parts & Accessories

• X2K-Exp-Red-2 NMEA Starter Kit — Complete NMEA 2000 Network Starter Kit
• Lowrance 000-0119-79 N2K-T-RD — NMEA 2000 T-Connector
• Lowrance 000-0119-75 N2K-PWR-RD — Red Power Cable
• Lowrance 000-0119-88 N2KEXT-2RD — 2 ft NMEA 2000 Network Extension Cable
• Lowrance 000-0127-53 — NMEA 2000 6' Network Extension Cable
• Simrad 000-10760-001 NMEA 2000 Micro-C Backbone Starter Kit — 4.5m / 15 ft
• Lenco NMEA 2000 Terminator Resistor Kit (Male/Female)