Crusader 8.1L Crankshaft Position Sensor | OEM Part R020034
Free returns on all eligible orders
You have 30 days to request a return. All sale items are final sale.
Crusader 8.1L Crankshaft Position Sensor — OEM Part R020034
Genuine OEM crankshaft position sensor for Crusader 8.1L marine gasoline engines. This sensor monitors crankshaft rotation and position, providing critical data to the engine control module (ECM) for precise ignition timing and fuel injection control. It is the correct OEM replacement for the crankshaft position sensor on compatible Crusader 8.1L engine applications.
Part Information
- Part Number: R020034
- Brand: Crusader / PCM (Pleasurecraft Marine Engine Group)
- Official Product Type: Crankshaft Position Sensor (CKP)
- System: Engine Management — Ignition & Fuel Injection
- Engine Family: 8.1L Marine Gasoline (V8)
Supersession & Cross-Reference
- Current OEM Part Number: R020034
- A related crankshaft position sensor for the 6.0L LQ4 engine is available as OEM Part R020044 — confirm which part number your engine requires before ordering
- Confirm the current part number against your engine’s parts diagram before ordering
Compatible Applications
- Crusader 8.1L marine gasoline engines where the parts diagram specifies crankshaft position sensor R020034
- PCM (Pleasurecraft Marine Engine Group) 8.1L engine applications using the same sensor specification
- Always confirm fitment by your exact engine model and serial number before ordering — sensor specifications can vary by production year and engine configuration
Serial Number & Fitment Notice
Verify fitment using your engine serial number and the corresponding parts diagram. Do not assume fitment based on engine displacement alone — the 8.1L platform uses different sensors across model years and configurations. Cross-reference R020034 against your engine’s parts diagram to confirm the correct sensor.
When to Replace
Replace this sensor when experiencing:
- No-start or hard-start conditions with no other obvious cause
- Engine misfires, rough running, or erratic idle
- Stalling under load or at speed
- ECM fault codes related to crankshaft position or engine speed signal
- Intermittent loss of spark or fuel injection events
Installation Notes
- Verify the correct air gap clearance between the sensor tip and the reluctor wheel during installation — refer to the Crusader/PCM service manual for your engine
- Ensure the electrical connector is fully seated and the wiring harness is routed away from heat sources
- Clear all ECM diagnostic fault codes after replacement
- Test engine operation and confirm the fault code does not return before returning the vessel to service
Technical FAQ
What happens if the crankshaft position sensor fails?
The ECM relies on the crankshaft position sensor to determine when to fire the ignition and inject fuel. A failed sensor typically results in a no-start condition or severe misfiring. In some cases, the engine may start intermittently before failing completely.
Can I test the sensor before replacing it?
Yes. A crankshaft position sensor can be tested with a multimeter for resistance and with a scan tool for signal output. However, intermittent failures may not show up on a static test — if the fault code points to the CKP sensor and other causes have been ruled out, replacement is the recommended course of action.
Is R020034 the same as R020044?
No. R020034 is the crankshaft position sensor for the 8.1L engine. R020044 is the sensor for the 6.0L LQ4 engine. These are different parts — confirm your engine displacement and part number before ordering.
Parts Desk Insights
Best Use Case: This is the correct OEM replacement for 8.1L Crusader engine owners diagnosing a no-start or misfire condition where ECM fault codes point to the crankshaft position sensor. It is also the right part for preventive replacement during a major engine service on high-hour engines where the original sensor has never been replaced.
Common Customer Issue: The most frequent ordering mistake is confusing R020034 (8.1L) with R020044 (6.0L LQ4). Both are Crusader/PCM crankshaft position sensors but they are not interchangeable. Always confirm your engine displacement and cross-reference the part number against your engine’s parts diagram before ordering.
Related Products
Shipping information
In-stock and OEM parts: ship same or next business day.
Locally warehoused items: ship within 1-3 business days.
Special-order items: timeline confirmed after order.
Returns & warranty
Returns & Satisfaction Guarantee
We stand firmly behind the quality of every product we sell. Your confidence matters to us — and we back it with a straightforward 30-Day Satisfaction Guarantee.
If you are not fully satisfied, you may request a return within 30 days of delivery. All returns must receive pre-approval prior to being sent back. Unauthorized returns will not be accepted.
To qualify for a return:
Item must be in new, unused condition
Product must be in its original packaging
All parts, components, hardware, manuals, and accessories must be included
Packaging must be undamaged and suitable for resale
Important:
Electronics are strictly inspected. No returns on open-box electronics. Exceptions may apply only with prior written approval. Any electronic unit that has been installed, powered, activated, or altered may not be eligible for return.
We are serious about product integrity — and equally serious about taking care of our customers. If there is ever a product issue, contact us immediately so we can make it right.
For return authorization, please contact our support team before shipping anything back.